SEA FOAM! WHAT IS IT AND WHY SHOULD YOU USE IT?
Over time, the internals of your engine get clogged up with all kinds of nasty stuff. Inside the crankcase, where the oil lives, varnish and tar build up on the surfaces of the pistons, rings, lifters and in the oil galleys that supply the oil to all the components. This lowers the engine’s ability to cool and lubricate itself, reducing the efficiency, performance, and life of the engine.
The same build up occurs inside the fuel system as well, clogging the injectors or carburetor jets, gumming up the intake valves and on the tops of the pistons too. If the valves don’t move freely, then your engine’s breathing is greatly hampered. Carbon deposits on the pistons and valves can lead to hot spots which cause detonation, which lowers your engine’s performance. The trick is how do you clean? Virtually every engine, from 2-stroke lawnmowers to big rig diesels face the same problem.
Sea Foam has been around for over 70 years, and it is one of the most trusted treatments for all engines. While Sea Foam makes a range of excellent products, the main one is Sea Foam Motor Treatment. Sea Foam is specially formulated to safely and slowly re-liquify the gum, sludge, varnish and carbon deposits from the hard parts in your engine so they can be flushed out of the system.
Sea Foam helps lubricate the moving parts, particularly in the fuel system. Ethanol additives dry out the seals and leaves a varnish that makes it harder for oil to lubricate the parts. Removing this varnish brings the engine back into top working order. Inside the fuel tank, Sea Foam absorbs water, allowing it to be burned up in the combustion chamber without issue.
How To Use Sea Foam
Sea Foam Motor Treatment can be used three ways: in the crankcase, in the fuel tank , and in the diesel fuel filter. For cleaning the top end, use Sea Foam Spray as directed.
IN THE CRANKCASE
When added to the oil, Sea Foam will clean up sludge, quiet noisy lifters, and remove oil varnish. One can treats 16 quarts of oil so you get 2 treatments in one can for most vehicles. The best method is to add the treatment 500-1000 miles before the next oil change, and then add the rest after you have changed the oil. This will get the big amounts of varnish and sludge out, and the second treatment keeps things clean.
IN THE FUEL
One can treats up to 16 gallons of fuel. This will remove deposits from the fuel pump, injectors or carb jets, control moisture, and stabilize the fuel. In diesel engines, it will de-ice and has anti-gel properties.
TOP-END
To clean carbon deposits from air intake systems, intake valves and combustion chambers inside the engine, including GDI engines, Sea Foam recommends using Sea Foam Spray Top Engine cleaner and lube (Part # SS-14). Sea Foam Spray is the same great Sea Foam only in aerosol spray instead of liquid form. Sea Foam Spray is used by inserting the included application hose and patented “HOOK TOOL” into the air intake just in front of the throttle plates in the throttle body. Then start engine and let it warm up to operating temperature. Increase idle speed to 2,000 RPM and spray the contents of the container into the engine. Shut the engine off and allow it to “Hot Soak” for 15 minutes. After the Hot Soak period restart the engine and road test the vehicle aggressively until the exhaust is clean (road test normally takes 5 to 10 miles of driving). Easy to follow directions are also available right on the Sea Foam Spray container.
Treatments like this may seem complicated, but with a little bit of prep work, you can do it yourself and restore your vehicle’s power and performance. If you have any concerns, stop by your local NAPA Auto Parts Store or NAPA AutoCare Center.
Check out all the chemical products available on NAPA Online or trust one of our 16,000 NAPA AutoCare locations for routine maintenance and repairs. For more information on Sea Foam Motor Treatment, chat with a knowledgeable expert at your local NAPA AUTO PARTS store.
